Dual SFF-8612 Oculink 4x Host to Dual Ruler 1U GEN-Z EDSFF 9.5mm 15mm 25mm Short SSD E1.S PCI-E with Heat Sink PM9A3 PM9D3 P5801X Carrier Adapter

Dual PCI-e 4x channel for oculink and EDSFF, Each ouclink port can connect one SSD to work.The converter can be installed into your system internally through the oculink SFF-8612 SFF-8611 PCI-E 4X interface.

EDSFF offers a dynamic range of form factors that have advantages vs the incumbent SSD form factors in capacity, scalability, performance, serviceability, manageability, thermal and power management.

This converter enables the connection of two GEN-Z SSD in E1.S. Fit for 9.5mm & 15mm & 25mm thickness SSD with heat sink.（like PM9A3 PM9D3 P5801X)

Thus an EDSFF E1.S SSD becomes an oculink SFF-8612 SFF-8611 PCI-E 4X SSD, which can be used in IoT, data center and server area.

The card transmits PCI Express 5.0/4.0 signals using the EDSFF protocol.Data transfer rate up to 64Gbps, Supports EDSFF Gen-Z SSD. This makes it suitable for use with the PCI-E5.0/4.0 generation of high-performance SSDs and other PCIe Gen5/Gen4 devices.

Oculink 4x connectors are internal and external small form factor PCI-E connectors optimized for the client and market. Compatible with T10/ SAS-4 24 Gbps, SFF-8611, SFF-8612, PCIe Gen 3 and Gen 4,Gen 5;

External Slimline Dual SFF-8654 8X 74Pin to PCIE 16X Express 3.0 PCIE4.0 Raid Card VROC Raid0 Hyper Adapter

One detachable PCIE PCI-Express 16x motherboard can be connected,The converter can be installed into the system internally through the SFF-8654 interface.

Only supports motherboards with detachable PCI-E channels; Control the operation of four disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.

Four PX410 PCI-Express Linear Redriver is a four-channel, low-power, high-performance linear repeater/redriver designed to support PCI Express (PCIe) Generation 1.0, 2.0, 3.0, and 4.0. The device is a protocol-agnostic linear redriver that can operate for interfaces up to 25Gbps.

The adapter features a built-in ReDriver circuit, which helps to boost signal quality and reduce noise interference over long cable lengths.

High-speed data transfer : The adapter is designed for use with ssd that use SFF-8654 8x connectors, allowing for fast and reliable data transfer at speeds of up to 64Gbps.

Easy to use: Simply plug in the SFF-8654 8x 74Pin end of the adapter into your device and the SFF-8654 8x 74pin end into your external GPU or drive, and you're ready to go.

It can be connected e.g. one SSD or eGPU Graphics Card by using an optional cable. Suitable for small hosts, desktops, laptops, etc. to convert PCIE sockets to SFF-8654 8X sockets, with fixing holes for fixing.

It transmits PCI Express 4.0 signals using the PCIE protocol; Support PCIE 4.0 data transmission, Data transfer rate up to 64Gbps, Support connecting GPU graphics card, SSD, expansion card, etc., backward compatible with PCIE 3.0.

Transform your works with this adapter, facilitating integration of PCI-E into systems requiring SFF-8654 connection;Elevates your system's capabilities with our adapter, ensuring a stable and robusts connection investments without compromising on space or convenience.

With 12cm standard bracket.

U.2 SFF-8639 Host to PCI-E Ruler 1U GEN-Z EDSFF 9.5mm 15mm 25mm Short SSD E1.S with Heat Sink PM9A3 PM9D3 P5801X Carrier Adapter

EDSFF offers a dynamic range of form factors that have advantages vs the incumbent SSD form factors in capacity, scalability, performance, serviceability, manageability, thermal and power management.

This converter enables the connection of a GEN-Z SSD in E1.S. Fit for 9.5mm & 15mm & 25mm thickness SSD with heat sink.（like PM9A3 PM9D3 P5801X)

The converter can be installed into your system internally through the U.2 SFF-8639 PCI-E 4X interface.

Thus an EDSFF E1.S SSD becomes an U.2 SSD, which can be used in IoT, data center and server area.

Compliant with PCI Express 5.0/4.0. No driver installation is required. Most of the latest operating systems support PCIe-NVMe SSDs.

PCI-E 4.0 PCI Express 1x to PCI-E 16x Extender Converter Riser Card Adapter PCBA Male to Female Compatible with Graphics Card Networking Adapter (1X-16X)

Please note that the actual data transfer speed of this PCIe4.0 slot depends on the speed of the PCI-E 1x interface. PCIe 4.0 backwards compatible with PCIe 3.0/2.0/1.0;

PCI-E 1X to PCIe 4.0 16X Extender can convert the PCI-E 1x slot on the motherboard into the PCIe 16X slot, which is used to connect various PCIe PCIe X8, X4 and X16 devices. To avoid damage to the device, ensure that the installation direction is correct.

This is PCI-e (PCI Express) Slot Relocate adapter; It is especially suitable for custom enclosures and low-profile rack mount chassis;No Driver necessary and not support hot swappable;Does not support hot-plugging.

The Slot PCI-Express 1x Riser Card makes the PCI Express 1x Card rise from motherboard , with the PCI Express socket directly in line with the socket on the motherboard.

This riser card faces away from the mainboard; Please ensure that PCIE cards are securely mounted in an EMI safe location, and that no shorts have occurred due to poor PCIE card placement.

PCI-E 4.0 PCI Express 8x to PCI-E 16x Extender Converter Riser Card Adapter PCBA Male to Female Compatible with Graphics Card Networking Adapter (8X-16X)

Please note that the actual data transfer speed of this PCIe4.0 slot depends on the speed of the PCI-E 8x interface. PCIe 4.0 backwards compatible with PCIe 3.0/2.0/1.0;

PCI-E 8X to PCIe 4.0 16X Extender can convert the PCI-E 8X slot on the motherboard into the PCIe 16X slot, which is used to connect various PCIe PCIe X8, X4 and X16 devices. To avoid damage to the device, ensure that the installation direction is correct.

This is PCI-e (PCI Express) Slot Relocate adapter; It is especially suitable for custom enclosures and low-profile rack mount chassis;No Driver necessary and not support hot swappable;Does not support hot-plugging.

The Slot PCI-Express 8x Riser Card makes the PCI Express 8x Card rise from motherboard , with the PCI Express socket directly in line with the socket on the motherboard.

This riser card faces away from the mainboard; Please ensure that PCIE cards are securely mounted in an EMI safe location, and that no shorts have occurred due to poor PCIE card placement.

PCI-E 4.0 PCI Express 4x to PCI-E 16x Extender Converter Riser Card Adapter PCBA Male to Female Compatible with Graphics Card Networking Adapter (4X-16X)

Please note that the actual data transfer speed of this PCIe4.0 slot depends on the speed of the PCI-E 4x interface. PCIe 4.0 backwards compatible with PCIe 3.0/2.0/1.0;

PCI-E 4X to PCIe 4.0 16X Extender can convert the PCI-E 4X slot on the motherboard into the PCIe 16X slot, which is used to connect various PCIe PCIe X8, X1 and X16 devices. To avoid damage to the device, ensure that the installation direction is correct.

This is PCI-e (PCI Express) Slot Relocate adapter; It is especially suitable for custom enclosures and low-profile rack mount chassis;No Driver necessary and not support hot swappable;Does not support hot-plugging.

The Slot PCI-Express 4x Riser Card makes the PCI Express 4x Card rise from motherboard , with the PCI Express socket directly in line with the socket on the motherboard.

This riser card faces away from the mainboard; Please ensure that PCIE cards are securely mounted in an EMI safe location, and that no shorts have occurred due to poor PCIE card placement.

PCI-E 4X Host Adapter to NVMe Ruler 1U GEN-Z EDSFF Short SSD E1.S Carrier Adapter

EDSFF offers a dynamic range of form factors that have advantages vs the incumbent SSD form factors in capacity, scalability, performance, serviceability, manageability, thermal and power management.

This converter enables the connection of a GEN-Z SSD in E1.S. Fit for 5.9mm & 8.0mm SSD without heat sink.

The converter can be installed into your system internally through the PCI-E 4X interface.

Thus an EDSFF E1.S SSD becomes an PCI-E SSD, which can be used in IoT, data center and server area.

Compliant with PCI Express 4.0. No driver installation is required. Most of the latest operating systems support PCIe-NVMe SSDs.

Low profile and Regular size PCIe bracket on board.

PCI-Express 4.0 PCIE 4x to Oculink SFF-8612 SFF-8611 Host Card for U.2 SSD eGPU External Graphics Card Dock

This PCI Express 4x card expands the PC by one SFF-8612 interface, It can be connected e.g. one SSD/eGPU using an optional cable. The card transmits PCI Express signals using the PCIE4.0 protocol.

Oculink is the next generation of high-speed internal and external I/O connectors for PCI-E, compatible with T10/ SAS-4 24 Gbps, SFF-8611, SFF-8612, PCIe Gen 3 and Gen 4.

It can be connected e.g. one SSD or eGPU Graphics Card by using an optional cable. Suitable for small hosts, desktops, laptops, etc. to convert PCIE sockets to Oculink sockets, with fixing holes for fixing.

It transmits PCI Express 4.0 signals using the PCIE protocol; Support PCIE 4.0 data transmission, Data transfer rate up to 64Gbps, Support connecting GPU graphics card, SSD, expansion card, etc., backward compatible with PCIE 3.0.

Transform your works with this cable adapter, facilitating integration of PCI-E into systems requiring OCuLink connection;Elevates your system's capabilities with our adapter, ensuring a stable and robusts connection investments without compromising on space or convenience.

Connectors:1xOCuLink SFF-8612 female and 1xPCI Express; with standard length and low profile bracket.

4X NVME M.2 NGFF SSD to Detachable Bifurcation PCIE Express 5.0 Gen5 Gen4 X16 Raid Card VROC Raid0 Hyper Adapter

1) The card does not support actual hardware raid, the product only supports the formation of Virtual raid under win10/win10 system, or the use of other third-party software to build raid.

2) Only supports motherboards with bifurcation detachable PCI-E channels; Control the operation of four disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk;NVME four-disks design, Stable installation, Can run four NVME disks at full speed at the same time.

3) Built-in multiple sets of high-power DC modules for sustainable and stable work; The innovative design can accommodate four NVMEs of the chassis, and can support simultaneous operation.

4) VROC is an enterprise RAID solution that unleashes the performance of NVMe SSDs, enabled by a feature in Scalable processors called Volume Management Device (VMD), an integrated controller inside the CPU PCIe root complex. VROC enables these benefits without the complexity, cost, and power consumption of traditional hardware RAID host bus adapter (HBA) cards placed between the drives and the CPU.

5) The bandwidth for each PCIe 5.0 lane is 4 GB/s. 4 GB/s per lane means that if you use a PCI-Express 5.0 x16 device, it would have up to 64 GB/s of bandwidth available to it.

6) NVMe PCIe add-in cards can use up to 16 lanes in an x16 slot, thus having up to 64 GB/s of bandwidth available to them with PCIe5.0; having up to 32GB/s of bandwidth available to them with PCIe4.0.

4X NVME M.2 AHCI to PCI-E Express 3.0 Gen3 X16 Raid Card with Fan VROC Raid0 Hyper Adapter

1.The product does not support hardware raid, the product only supports the formation of soft raid under win10 system, or the use of other third-party software to build raid.

2.Only supports motherboards with detachable PCIE channels.Control the operation of four disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk

3.NVME four-disk design, Stable installation, Can run 4 NVME disks at full speed at the same time.

4.Support 2U server small chassis installation, Built-in multiple sets of high-power DC modules for sustainable and stable work.

5.The innovative design can accommodate four NVMEs on both sides of the half-height chassis, and can support simultaneous operation.

4X NVME M.2 AHCI to PCIE Express 3.0 Gen3 X16 Raid Card VROC Raid0 Hyper Adapter

1.The product does not support hardware raid, the product only supports the formation of soft raid under win10 system, or the use of other third-party software to build raid.

2.Only supports motherboards with detachable PCIE channels.Control the operation of four disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk

3.NVME four-disk design, Stable installation, Can run 4 NVME disks at full speed at the same time.

4.Support 2U server small chassis installation, Built-in multiple sets of high-power DC modules for sustainable and stable work.

5.The innovative design can accommodate four NVMEs on both sides of the half-height chassis, and can support simultaneous operation.

2X NVME M.2 AHCI to PCIE Express 3.0 Gen3 X8 X16 Raid Card VROC Raid0 Hyper Adapter

1.The product does not support hardware raid, the product only supports the formation of soft raid under win10 system, or the use of other third-party software to build raid.

2.Only supports motherboards with detachable PCI-E channels.Control the operation of two disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.

3.NVME two-disks design, Stable installation, Can run 2 NVME disks at full speed at the same time.

4.Built-in multiple sets of high-power DC modules for sustainable and stable work.

5.The innovative design can accommodate two NVMEs of the chassis, and can support simultaneous operation.

Dual Ports PCI-E PCI Express 1x to 2500Mbps 2.5Gbps 2500Mbps GBE Gigabit 1000Mbps Ethernet Network LAN Cable Adapter for Desktop Motherboard

Dual Port 2.5G Network Card; By inserting a PCIe network card into the PCI Express x1 slot, you can upgrade the host with one more RJ45 port. It's a perfect choice for a Desktop PC that is fewer network ports or network port failure to connect to the wired network.

2.5G High-Speed Transmission: This 2.5G network card ushers in a new era of network transmission speed, offering speeds up to 2.5 times faster than traditional gigabit rates. It provides an exceptional online experience, ensuring swift file transfers, seamless HD video streaming, and lag-free online gaming.Support PXE, Auto MDIX, IEEE 802.1Q VLAN tagging, IEEE802.3bz(2.5GBASE-T), Full Duplex flow control(IEEE 802.3x), IEEE 802.1P Layer 2 Priority Encoding.

PCIe 1x to RJ45: It accommodates various PCI Express slot configurations, such as x1, x4, x8, and x16, enabling seamless installation and interchangeability across different motherboards to meet diverse hardware layouts and needs. Note: Compatible with PCI-E slots only, not for PCI slots.

Multiple OS Compatibility: Compatible with Windows 11, Windows 10, and Linux systems, this network card guarantees seamless compatibility. Support multiple installation such as PC, server, workstation, NAS, This eradicates worries about system compatibility and grants you the complete convenience of high-speed networking.

Low Profile Flexible Bracket Versatility: Engineered with low-profile and standard bracket, this 2.5G network card provides heightened flexibility for diverse computer arrangements. Irrespective of your computer's specifications, effortless installation is ensured, optimizing your hardware setup.

Up to 2.5 Gigabit with Realtek RTL8125B chip, compatibe 1Gbps/100M/10M auto-negotiation, support standard Cat5e or above UTP at distances up to 100m; Minimizes electromagnetic interference, enhancing stability and reliability with every connection. Excellent heat dissipation can reduce the temperature quickly and maintain the stability of network transmission.

2500Mbps 2.5Gbps to Mini PCI-E PCI Express GBE Gigabit 1000Mbps Ethernet Network LAN Cable Adapter for Desktop Motherboard

2.5G High-Speed Transmission: This 2.5G network card ushers in a new era of network transmission speed, offering speeds up to 2.5 times faster than traditional gigabit rates. It provides an exceptional online experience, ensuring swift file transfers, seamless HD video streaming, and lag-free online gaming.Support PXE, Auto MDIX, IEEE 802.1Q VLAN tagging, IEEE802.3bz(2.5GBASE-T), Full Duplex flow control(IEEE 802.3x), IEEE 802.1P Layer 2 Priority Encoding.

Mini PCIe to RJ45: It accommodates various Mini PCI Express slot configurations, enabling seamless installation and interchangeability across different motherboards to meet diverse hardware layouts and needs. Note: Compatible with Mini PCI-E slots only, not for PCI/PCI-E slots.

Multiple OS Compatibility: Compatible with Windows 11, Windows 10, and Linux systems, this network card guarantees seamless compatibility. Support multiple installation such as PC, server, workstation, NAS, This eradicates worries about system compatibility and grants you the complete convenience of high-speed networking.

Low Profile Flexible Versatility: Engineered with low-profile bracket, this 2.5G network card provides heightened flexibility for diverse computer arrangements. Irrespective of your computer's specifications, effortless installation is ensured, optimizing your hardware setup.

Up to 2.5 Gigabit with Realtek RTL8125B chip, compatibe 1Gbps/100M/10M auto-negotiation, support standard Cat5e or above UTP at distances up to 100m; Minimizes electromagnetic interference, enhancing stability and reliability with every connection. Excellent heat dissipation can reduce the temperature quickly and maintain the stability of network transmission.

2500Mbps 2.5Gbps to 2230 NGFF A+E-Key GBE Gigabit 1000Mbps Ethernet Network LAN Cable Adapter for Desktop Motherboard

2.5G High-Speed Transmission: This 2.5G network card ushers in a new era of network transmission speed, offering speeds up to 2.5 times faster than traditional gigabit rates; It provides an exceptional online experience, ensuring swift file transfers, seamless HD video streaming, and lag-free online gaming.Support PXE, Auto MDIX, IEEE 802.1Q VLAN tagging, IEEE802.3bz(2.5GBASE-T), Full Duplex flow control(IEEE 802.3x), IEEE 802.1P Layer 2 Priority Encoding.

2230 NGFF A+E-Key to RJ45: It accommodates various 2230 NGFF A+E-Key slot configurations, enabling seamless installation and interchangeability across different motherboards to meet diverse hardware layouts and needs. Note: Compatible with 2230 NGFF A+E-Key slots only, not for B-Key M-Key slots.

Multiple OS Compatibility: Compatible with Windows 11, Windows 10, and Linux systems, this network card guarantees seamless compatibility. Support multiple installation such as PC, server, workstation, NAS, This eradicates worries about system compatibility and grants you the complete convenience of high-speed networking.

Low Profile Flexible Versatility: Engineered with low-profile bracket, this 2.5G network card provides heightened flexibility for diverse computer arrangements. Irrespective of your computer's specifications, effortless installation is ensured, optimizing your hardware setup.

Up to 2.5 Gigabit with Realtek RTL8125B chip, compatibe 1Gbps/100M/10M auto-negotiation, support standard Cat5e or above UTP at distances up to 100m; Minimizes electromagnetic interference, enhancing stability and reliability with every connection. Excellent heat dissipation can reduce the temperature quickly and maintain the stability of network transmission.

PCI-E PCI Express 1x to 2500Mbps 2.5Gbps 2500Mbps GBE Gigabit 1000Mbps Ethernet Network LAN Cable Adapter for Desktop Motherboard

2.5G High-Speed Transmission: This 2.5G network card ushers in a new era of network transmission speed, offering speeds up to 2.5 times faster than traditional gigabit rates. It provides an exceptional online experience, ensuring swift file transfers, seamless HD video streaming, and lag-free online gaming.Support PXE, Auto MDIX, IEEE 802.1Q VLAN tagging, IEEE802.3bz(2.5GBASE-T), Full Duplex flow control(IEEE 802.3x), IEEE 802.1P Layer 2 Priority Encoding.

PCIe 1x to RJ45: It accommodates various PCI Express slot configurations, such as x1, x4, x8, and x16, enabling seamless installation and interchangeability across different motherboards to meet diverse hardware layouts and needs. Note: Compatible with PCI-E slots only, not for PCI slots.

Multiple OS Compatibility: Compatible with Windows 11, Windows 10, and Linux systems, this network card guarantees seamless compatibility. Support multiple installation such as PC, server, workstation, NAS, This eradicates worries about system compatibility and grants you the complete convenience of high-speed networking.

Low Profile Flexible Bracket Versatility: Engineered with low-profile and standard bracket, this 2.5G network card provides heightened flexibility for diverse computer arrangements. Irrespective of your computer's specifications, effortless installation is ensured, optimizing your hardware setup.

Up to 2.5 Gigabit with Realtek RTL8125B chip, compatibe 1Gbps/100M/10M auto-negotiation, support standard Cat5e or above UTP at distances up to 100m; Minimizes electromagnetic interference, enhancing stability and reliability with every connection. Excellent heat dissipation can reduce the temperature quickly and maintain the stability of network transmission.

Low Profile Slimline Dual SFF-8654 8X 74Pin to PCIE 16X Express 3.0 PCIE4.0 Raid Card VROC Raid0 Hyper Adapter

One detachable PCIE PCI-Express 16x motherboard can be connected,The converter can be installed into the system internally through the SFF-8654 interface.

Only supports motherboards with detachable PCI-E channels; Control the operation of four disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.

High-speed data transfer : The adapter is designed for use with ssd that use SFF-8654 8x connectors, allowing for fast and reliable data transfer at speeds of up to 64Gbps.

Easy to use: Simply plug in the SFF-8654 8x 74Pin end of the adapter into your device and the SFF-8654 8x 74pin end into your external GPU or drive, and you're ready to go.

It can be connected e.g. one SSD or eGPU Graphics Card by using an optional cable. Suitable for small hosts, desktops, laptops, etc. to convert PCIE sockets to SFF-8654 8X sockets, with fixing holes for fixing.

It transmits PCI Express 4.0 signals using the PCIE protocol; Support PCIE 4.0 data transmission, Data transfer rate up to 64Gbps, Support connecting GPU graphics card, SSD, expansion card, etc., backward compatible with PCIE 3.0.

Transform your works with this adapter, facilitating integration of PCI-E into systems requiring SFF-8654 connection;Elevates your system's capabilities with our adapter, ensuring a stable and robusts connection investments without compromising on space or convenience.

Internal Low Profile PCBA,Without bracket.

External Slimline Dual SFF-8654 8X 74Pin to PCIE 16X Express 3.0 PCIE4.0 Raid Card VROC Raid0 Hyper Adapter

One detachable PCIE PCI-Express 16x motherboard can be connected,The converter can be installed into the system internally through the SFF-8654 interface.

Only supports motherboards with detachable PCI-E channels; Control the operation of four disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.

High-speed data transfer : The adapter is designed for use with ssd that use SFF-8654 8x connectors, allowing for fast and reliable data transfer at speeds of up to 64Gbps.

Easy to use: Simply plug in the SFF-8654 8x 74Pin end of the adapter into your device and the SFF-8654 8x 74pin end into your external GPU or drive, and you're ready to go.

It can be connected e.g. one SSD or eGPU Graphics Card by using an optional cable. Suitable for small hosts, desktops, laptops, etc. to convert PCIE sockets to SFF-8654 8X sockets, with fixing holes for fixing.

It transmits PCI Express 4.0 signals using the PCIE protocol; Support PCIE 4.0 data transmission, Data transfer rate up to 64Gbps, Support connecting GPU graphics card, SSD, expansion card, etc., backward compatible with PCIE 3.0.

Transform your works with this adapter, facilitating integration of PCI-E into systems requiring SFF-8654 connection;Elevates your system's capabilities with our adapter, ensuring a stable and robusts connection investments without compromising on space or convenience.

With 12cm standard bracket.

External Slimline SFF-8654 8X 74Pin to PCIE Express 3.0 PCIE4.0 Raid Card VROC Raid0 Hyper Adapter

One detachable PCIE PCI-Express 8x motherboard can be connected,The converter can be installed into the system internally through the SFF-8654 interface.

Only supports motherboards with detachable PCI-E channels; Control the operation of two disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.

High-speed data transfer : The adapter is designed for use with ssd that use SFF-8654 8x connectors, allowing for fast and reliable data transfer at speeds of up to 32Gbps.

Easy to use: Simply plug in the SFF-8654 8x 74Pin end of the adapter into your device and the SFF-8654 8x 74pin end into your external hard drive, and you're ready to go.

It can be connected e.g. one SSD or eGPU Graphics Card by using an optional cable. Suitable for small hosts, desktops, laptops, etc. to convert PCIE sockets to SFF-8654 8X sockets, with fixing holes for fixing.

It transmits PCI Express 4.0 signals using the PCIE protocol; Support PCIE 4.0 data transmission, Data transfer rate up to 32Gbps, Support connecting GPU graphics card, SSD, expansion card, etc., backward compatible with PCIE 3.0.

Transform your works with this cable adapter, facilitating integration of PCI-E into systems requiring SFF-8654 connection;Elevates your system's capabilities with our adapter, ensuring a stable and robusts connection investments without compromising on space or convenience.

With 8cm low profile and 12cm standard bracket.

External MCIO 8i Mini Cool Edge IO SFF-TA-1016 to PCIE5.0 PCI-Express 8x VROC Adapter for Mainboard SSD Graphics Card

One detachable PCIE PCI-Express 8x motherboard can be connected,The converter can be installed into the system internally through the MCIO interface.

Only supports motherboards with detachable PCI-E channels.Control the operation of two disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.Built-in multiple sets of high-power DC modules for sustainable and stable work.

PCI-E Express 16X to 16x Riser Extender Card with Molex IDE Power Ribbon Cable 20cm

Layer PCB bard designing.1-slot PCI-E 16X riser card with normal ribbon cable.high speed FFC cable is flexible for 1U,2U,3U chassis.

Support PCIe 1X card and 4X,8X,16X card.Extra molex(12V/GND) power supply for PCI-e video card.

PCI-Express PCI-E to 16X Riser Card Flexible Ribbon Extender Cable w/Molex + Solid Capacitor

The Flexible Single Slot PCI-Express Riser Card with x1 to x16 interface makes the PCI-Express x16 Card away from motherboard , with the PCI-Express socket x16 directly in line with the socket on the motherboard.

It is flexible cable design and suitable for your own projects,This riser card provides expansion for 1 slots with cable. Gold plated contacts for best conductivity and long life.


Great for intense Gaming,Works for all PCI-e bus versions,Ensure proper airflow in your system by creating more room in tight-fit cases.

PCI-E Express 4x To 16x Extension Flex Cable Extender Converter Riser Card Adapter 20cm

Withe 4pin power,layer PCB bard designing.1-slot PCI-E 4X riser card with normal ribbon cable.

high speed FFC cable is flexible for 1U,2U,3U chassis.Support PCIe 4X card and 8X,16X card( only provide 4X speed).

PCI-Express PCI-E 4X to 16X Riser Card Flexible Ribbon Extender Cable w/Molex + Solid Capacitor

The Flexible Single Slot PCI-Express Riser Card with x1 to x16 interface makes the PCI-Express x16 Card away from motherboard , with the PCI-Express socket x16 directly in line with the socket on the motherboard.

It is flexible cable design and suitable for your own projects,This riser card provides expansion for 1 slots with cable. Gold plated contacts for best conductivity and long life.


Great for intense Gaming,Works for all PCI-e bus versions,Ensure proper airflow in your system by creating more room in tight-fit cases.

PCI-E 5.0 Mini Cool Edge IO MCIO STR PCI-E 16x 124Pin Male to MCIO 124Pin Male Extender Cable 50cm with Pull Tab

High-speed data transfer: This cable is designed for use with ssd that use MICO 16x connectors, allowing for fast and reliable data transfer at speeds of up to 64Gbps.

Easy to use: Simply plug in the MCIO 124Pin end of the cable into your device and the MCIO end into your external pcie device or drive, and you're ready to go.

Mini Cool Edge IO (MCIO) cable assemblies,These products can provide high performing channels with the added flexibility of where/how to use signals in your system.

What is mini cool edge Io (MCIO): MCIO cables are designed for data center, networking and telecommunications markets that use SAS, PCIe, Ethernet and othersignal protocols.

The solution can support cable to board and card to board applications in system, which include chip to chip, chiptomodule, chip to board and card edge option.

High-performance cable for networking and server equipment: The MCIO Mini Cool Edge IO is designed to support a wide range of protocols, including SAS, PCIe, Ethernet, and more, ensuring optimal performance for your equipment.

Industry standards: Support for SAS 3.0/4.0, PCIe Gen 3/4/5, 25G Ethernet, and 56GT/s PAM4 means that you can trust that your equipment will perform at optimal levels without any signal loss or degradation.

High frequency comply with PCI-E gen 5 requirement; cable and connector impedance 85ohm.

With the industry need for compactness, We are looking to achieve high-speed data transmission requirements in a space-saving design. MCIO Connectors and Cable Assemblies offer a slim form factor to preserve space and improve design flexibility in limited real estate applications.

MCIO products offer data transmission rates of up to 64Gbps, meeting PCIe Generation 6 specifications. These robust mechanical connectors are designed to protect the connector pins and ensure proper alignment during assembly for consistent signal integrity.

Dual Slimline SFF-8654 8X 4 NVME to PCIE Express 3.0 4.0 Raid Card VROC Raid0 Hyper Adapter

1.The product does not support hardware raid, the product only supports the formation of virtual raid under win10 system, or the use of other third-party software to build raid.

2.Only supports motherboards with detachable PCI-E channels.Control the operation of two disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.

3.Dual Slimline SFF-8654 8X design, Stable installation, Can run 4 PCIE disks at full speed at the same time.

4.Built-in multiple sets of high-power DC modules for sustainable and stable work.

5.The innovative design can accommodate Four PCIEs of the chassis, and can support simultaneous operation.

PCI-Express 4.0 PCIE 16x Detachable to Four Oculink SFF-8612 SFF-8611 VROC Raid0 Adapter for U.2 SSD eGPU External Graphics Card Dock

One detachable PCIE PCI-Express motherboard can be connected,The converter can be installed into the system internally through the oculink interface.

Only supports motherboards with detachable PCI-E channels.Control the operation of four disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.

This PCI Express card expands the PC by one SFF-8612 interface, It can be connected e.g. one SSD/eGPU using an optional cable. The card transmits PCI Express signals using the PCIE4.0 protocol.

Oculink is the next generation of high-speed internal and external I/O connectors for PCI-E, compatible with T10/ SAS-4 24 Gbps, SFF-8611, SFF-8612, PCIe Gen 3 and Gen 4.

It can be connected e.g. one SSD or eGPU Graphics Card by using an optional cable. Suitable for small hosts, desktops, laptops, etc. to convert PCIE sockets to Oculink sockets, with fixing holes for fixing.

It transmits PCI Express 4.0 signals using the PCIE protocol; Support PCIE 4.0 data transmission, Data transfer rate up to 64Gbps, Support connecting GPU graphics card, SSD, expansion card, etc., backward compatible with PCIE 3.0.

Transform your works with this cable adapter, facilitating integration of PCI-E into systems requiring OCuLink connection;Elevates your system's capabilities with our adapter, ensuring a stable and robusts connection investments without compromising on space or convenience.

Connectors:4x external OCuLink SFF-8612 female and 1xPCI Express; with standard length bracket.

PCI-Express 4.0 PCIE 16x Detachable to Four Oculink SFF-8612 SFF-8611 VROC Raid0 Adapter for U.2 SSD eGPU External Graphics Card Dock

One detachable PCIE PCI-Express motherboard can be connected,The converter can be installed into the system internally through the oculink interface.

Only supports motherboards with detachable PCI-E channels.Control the operation of four disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.

This PCI Express card expands the PC by one SFF-8612 interface, It can be connected e.g. one SSD/eGPU using an optional cable. The card transmits PCI Express signals using the PCIE4.0 protocol.

Oculink is the next generation of high-speed internal and external I/O connectors for PCI-E, compatible with T10/ SAS-4 24 Gbps, SFF-8611, SFF-8612, PCIe Gen 3 and Gen 4.

It can be connected e.g. one SSD or eGPU Graphics Card by using an optional cable. Suitable for small hosts, desktops, laptops, etc. to convert PCIE sockets to Oculink sockets, with fixing holes for fixing.

It transmits PCI Express 4.0 signals using the PCIE protocol; Support PCIE 4.0 data transmission, Data transfer rate up to 64Gbps, Support connecting GPU graphics card, SSD, expansion card, etc., backward compatible with PCIE 3.0.

Transform your works with this cable adapter, facilitating integration of PCI-E into systems requiring OCuLink connection;Elevates your system's capabilities with our adapter, ensuring a stable and robusts connection investments without compromising on space or convenience.

Connectors:four internal OCuLink SFF-8612 female and 1xPCI Express; with standard length and low profile bracket.

PCI-Express 4.0 PCIE 8x Detachable to Dual Oculink SFF-8612 SFF-8611 VROC Raid0 Adapter for U.2 SSD eGPU External Graphics Card Dock

One detachable PCIE PCI-Express motherboard can be connected,The converter can be installed into the system internally through the oculink interface.

Only supports motherboards with detachable PCI-E channels.Control the operation of two disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.

This PCI Express card expands the PC by one SFF-8612 interface, It can be connected e.g. one SSD/eGPU using an optional cable. The card transmits PCI Express signals using the PCIE4.0 protocol.

Oculink is the next generation of high-speed internal and external I/O connectors for PCI-E, compatible with T10/ SAS-4 24 Gbps, SFF-8611, SFF-8612, PCIe Gen 3 and Gen 4.

It can be connected e.g. one SSD or eGPU Graphics Card by using an optional cable. Suitable for small hosts, desktops, laptops, etc. to convert PCIE sockets to Oculink sockets, with fixing holes for fixing.

It transmits PCI Express 4.0 signals using the PCIE protocol; Support PCIE 4.0 data transmission, Data transfer rate up to 64Gbps, Support connecting GPU graphics card, SSD, expansion card, etc., backward compatible with PCIE 3.0.

Transform your works with this cable adapter, facilitating integration of PCI-E into systems requiring OCuLink connection;Elevates your system's capabilities with our adapter, ensuring a stable and robusts connection investments without compromising on space or convenience.

Connectors:Two external OCuLink SFF-8612 female and 1xPCI Express; with standard length and low profile bracket.

PCI-Express 4.0 PCIE 1x to Oculink SFF-8612 SFF-8611 Host Card for U.2 SSD eGPU External Graphics Card Dock

This PCI Express 1x card expands the PC by one SFF-8612 interface, It can be connected e.g. one SSD/eGPU using an optional cable. The card transmits PCI Express signals using the PCIE4.0 protocol.

Oculink is the next generation of high-speed internal and external I/O connectors for PCI-E, compatible with T10/ SAS-4 24 Gbps, SFF-8611, SFF-8612, PCIe Gen 3 and Gen 4.

It can be connected e.g. one SSD or eGPU Graphics Card by using an optional cable. Suitable for small hosts, desktops, laptops, etc. to convert PCIE sockets to Oculink sockets, with fixing holes for fixing.

It transmits PCI Express 4.0 signals using the PCIE protocol; Support PCIE 4.0 data transmission, Data transfer rate up to 64Gbps, Support connecting GPU graphics card, SSD, expansion card, etc., backward compatible with PCIE 3.0.

Transform your works with this cable adapter, facilitating integration of PCI-E into systems requiring OCuLink connection;Elevates your system's capabilities with our adapter, ensuring a stable and robusts connection investments without compromising on space or convenience.

Connectors:1xOCuLink SFF-8612 female and 1xPCI Express; with standard length and low profile bracket.

PCI-E 3.0 Express 4.0 x4 to Oculink SFF-8612 SFF-8611 Host Adapter for PCIe SSD with Bracket

This PCI Express card expands the PC by one SFF-8612 interface.

It can be connected e.g. one SSD by using an optional cable.

The card transmits PCI Express signals using the NVMe protocol.



Specification

Connectors:

1 x OCuLink SFF-8612 female

1 x PCI Express x4, V3.0

Data transfer rate up to 32 Gbps

Bootable, ex UEFI version 2.3.1

Supports NVM Express (NVMe) 1.2


System requirements

Linux Kernel 4.3 or above

Windows 8.1/8.1-64/10/10-64

PC with one free PCI Express x4 / x8 / x16 / x32 slot

PCI-E 3.0 Express 4.0 x4 to Oculink SFF-8612 SFF-8611 Host Adapter for PCIe SSD with Bracket

This PCI Express card expands the PC by one SFF-8612 interface.It can be connected e.g. one SSD by using an optional cable.The card transmits PCI Express signals using the NVMe protocol.

Oculink is the next generation of high-speed internal and external I/O connectors for servers, compatible with T10/ SAS-4 24 Gbps, SFF-8611, SFF-8612, PCIe Gen 3 and Gen 4.

It can be connected e.g. one SSD or eGPU Graphics Card by using an optional cable. Suitable for small hosts, desktops, laptops, etc. to convert M.2 sockets to Oculink sockets, with fixing holes for fixing.

It transmits PCI Express 4.0 signals using the NVMe protocol; Support PCIE 4.0 data transmission, Data transfer rate up to 64Gbps, Supports NVM Express (NVMe) 1.2. support connecting GPU graphics card, SSD, expansion card, etc., backward compatible with PCIE 3.0.

Transform your works with this cable adapter, facilitating integration of PCI-E 4x into systems requiring OCuLink connection;Elevates your system's capabilities with our adapter, ensuring a stable and robusts connection investments without compromising on space or convenience.

Specification

Connectors:

1 x OCuLink SFF-8612 female

1 x PCI Express x4, V3.0

Data transfer rate up to 32 Gbps

Bootable, ex UEFI version 2.3.1

Supports NVM Express (NVMe) 1.2


System requirements

Linux Kernel 4.3 or above

Windows 8.1/8.1-64/10/10-64

PC with one free PCI Express x4 / x8 / x16 / x32 slot

NVMe NGFF M-key 4X to PCI-E Ruler 1U GEN-Z EDSFF Short SSD E1.S Host Carrier Adapter

This converter enables the connection of a M.2 SSD in 2280 and 2260/2242/2230 format.

The converter can be installed into your system internally through the EDSFF E1.S interface.

Thus an M.2 SSD becomes an EDSFF E1.S SSD, which can be used in IoT, data center and server area.

Supports M.2 modules with key M or key B+M based on PCIe

Maximum height of the components on the module: 1.5 mm, application of double-sided assembled modules supported.

Connectors: 1 x EDSFF E1.S male to 1 x 67 pin M.2 key M slot

Interface: PCIe x4 Rev. 4.0

Low Profile Dual 2x NVME M.2 SSD to PCIE Express Gen4 X8 X16 Raid Card VROC Raid0 Hyper Adapter

1.The product does not support hardware raid, the product only supports the formation of Vroc soft raid under win10/win11 system, or the use of other third-party software to build raid.

2.Only supports motherboards with bifurcation detachable PCI-E channels.Control the operation of two disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.NVME dual-disks design, Stable installation, Can run dual NVME disks at full speed at the same time.

3.Built-in multiple sets of high-power DC modules for sustainable and stable work.The innovative design can accommodate two NVMEs of the chassis, and can support simultaneous operation.

4.Low Profile design: The low profile type Allowing you to connect it to 1U PCI-E port, even if space around the port is limited.

5.VROC is an enterprise RAID solution that unleashes the performance of NVMe SSDs, enabled by a feature in Scalable processors called Volume Management Device (VMD), an integrated controller inside the CPU PCIe root complex. VROC enables these benefits without the complexity, cost, and power consumption of traditional hardware RAID host bus adapter (HBA) cards placed between the drives and the CPU.

Please use the jumper to change the 12V/5V volt first. Otherwise it will be damaged your device.

DC 12V 5V Output Power System Intelligent Control Management System Power Card with PCI-E Bracket

It can work for DC12/5V Monitor,Router,Switch,Camera,Disk device. (No need power supply anymore)

Support: ATX standard chassis with PCI-E 12cm height bracket.

Advantages: safe and stable DC 12V 5V independent power control and management system, lead-free high temperature SMT, durable.

Input: SATA-15pin or IDE-4Pin, support DC12V and 5V power from internal chassis. Anyone is ok.

Output 1: DC5.5mm 12/5V out, Please use the jumper to change it.

Output 2: DC5.5mm 12V out, Can change it.

Output 3: DC 2Pin 12/5V out, Please use the jumper to change it.

Attached one DC5.5mm 1-to-4 Power cable, you can use it for

DC5.5*2.5mm,DC5.5*2.1mm,DC4.9*1.7mm,DC3.5*1.3mm output.

Package included one card and one cable.

PCI-E 5.0 Mini Cool Edge IO MCIO STR PCI-E 8i 74Pin Male to Dual MCIO 38Pin Male Extender Cable 50cm

High-speed data transfer: This cable is designed for use with ssd that use MICO 8x connectors, allowing for fast and reliable data transfer at speeds of up to 24 Gbps.

Easy to use: Simply plug in the MCIO 74 Pin end of the cable into your device and the MCIO 38pin end into your external hard drive, and you're ready to go.

Mini Cool Edge IO (MCIO) cable assemblies,These products can provide high performing channels with the added flexibility of where/how to use signals in your system.

What is mini cool edge Io (MCIO): MCIO cables are designed for data center, networking and telecommunications markets that use SAS, PCIe, Ethernet and othersignal protocols.

The solution can support cable to board and card to board applications in system, which include chip to chip, chiptomodule, chip to board and card edge option.

High-performance cable for networking and server equipment: The MCIO Mini Cool Edge IO is designed to support a wide range of protocols, including SAS, PCIe, Ethernet, and more, ensuring optimal performance for your equipment.

Industry standards: Support for SAS 3.0/4.0, PCIe Gen 3/4/5, 25G Ethernet, and 56GT/s PAM4 means that you can trust that your equipment will perform at optimal levels without any signal loss or degradation.

PCI-E 5.0 Mini Cool Edge IO MCIO STR PCI-E 8i 74Pin Male to MCIO 74Pin Male Extender Cable 50cm

High-speed data transfer: This cable is designed for use with ssd that use MICO 8x connectors, allowing for fast and reliable data transfer at speeds of up to 24 Gbps.

Easy to use: Simply plug in the MCIO 74 Pin end of the cable into your device and the MCIO end into your external hard drive, and you're ready to go.

Mini Cool Edge IO (MCIO) cable assemblies,These products can provide high performing channels with the added flexibility of where/how to use signals in your system.

What is mini cool edge Io (MCIO): MCIO cables are designed for data center, networking and telecommunications markets that use SAS, PCIe, Ethernet and othersignal protocols.

The solution can support cable to board and card to board applications in system, which include chip to chip, chiptomodule, chip to board and card edge option.

High-performance cable for networking and server equipment: The MCIO Mini Cool Edge IO is designed to support a wide range of protocols, including SAS, PCIe, Ethernet, and more, ensuring optimal performance for your equipment.

Industry standards: Support for SAS 3.0/4.0, PCIe Gen 3/4/5, 25G Ethernet, and 56GT/s PAM4 means that you can trust that your equipment will perform at optimal levels without any signal loss or degradation.

PCI-E 5.0 Mini Cool Edge IO MCIO Angled PCI-E 8i 74Pin Male to MCIO 74Pin Male Extender Cable 35cm

The angled type Allowing you to connect it to a female port, even if space around the port is limited.

High-speed data transfer: This cable is designed for use with ssd that use MICO 8x connectors, allowing for fast and reliable data transfer at speeds of up to 24 Gbps.

Easy to use: Simply plug in the MCIO 74 Pin end of the cable into your device and the MCIO end into your external hard drive, and you're ready to go.

Mini Cool Edge IO (MCIO) cable assemblies,These products can provide high performing channels with the added flexibility of where/how to use signals in your system.

What is mini cool edge Io (MCIO): MCIO cables are designed for data center, networking and telecommunications markets that use SAS, PCIe, Ethernet and othersignal protocols.

The solution can support cable to board and card to board applications in system, which include chip to chip, chiptomodule, chip to board and card edge option.

High-performance cable for networking and server equipment: The MCIO Mini Cool Edge IO is designed to support a wide range of protocols, including SAS, PCIe, Ethernet, and more, ensuring optimal performance for your equipment.

Industry standards: Support for SAS 3.0/4.0, PCIe Gen 3/4/5, 25G Ethernet, and 56GT/s PAM4 means that you can trust that your equipment will perform at optimal levels without any signal loss or degradation.

PCI-E 5.0 Mini Cool Edge IO MCIO PCI-E 8i 74Pin Male to Slimline SFF-8654 SAS 4.0 74Pin Male Extender Cable 50cm

High-speed data transfer: This cable is designed for use with ssd that use MICO to SFF-8654 connectors, allowing for fast and reliable data transfer at speeds of up to 24 Gbps.

Easy to use: Simply plug in the SFF-8654 74 Pin end of the cable into your device and the MCIO end into your external hard drive, and you're ready to go.

Mini Cool Edge IO (MCIO) cable assemblies,These products can provide high performing channels with the added flexibility of where/how to use signals in your system.

What is mini cool edge Io (MCIO): MCIO cables are designed for data center, networking and telecommunications markets that use SAS, PCIe, Ethernet and othersignal protocols.

The solution can support cable to board and card to board applications in system, which include chip to chip, chiptomodule, chip to board and card edge option.

High-performance cable for networking and server equipment: The MCIO Mini Cool Edge IO is designed to support a wide range of protocols, including SAS, PCIe, Ethernet, and more, ensuring optimal performance for your equipment.

Industry standards: Support for SAS 3.0/4.0, PCIe Gen 3/4/5, 25G Ethernet, and 56GT/s PAM4 means that you can trust that your equipment will perform at optimal levels without any signal loss or degradation.

PCI-E 5.0 Mini Cool Edge IO MCIO PCI-E 4i 38Pin Male to MCIO 4i SFF-TA-1016 Extender Cable 50cm

High-speed data transfer: This cable is designed for use with ssd that use 4x MICO to MICO connectors, allowing for fast and reliable data transfer at speeds of up to 24 Gbps.

Easy to use: Simply plug in the MCIO end of the cable into your device and the MCIO end into your external hard drive, and you're ready to go.

Mini Cool Edge IO (MCIO) cable assemblies,These products can provide high performing channels with the added flexibility of where/how to use signals in your system.

What is mini cool edge Io (MCIO): MCIO cables are designed for data center, networking and telecommunications markets that use SAS, PCIe, Ethernet and othersignal protocols.

The solution can support cable to board and card to board applications in system, which include chip to chip, chiptomodule, chip to board and card edge option.

High-performance cable for networking and server equipment: The MCIO Mini Cool Edge IO is designed to support a wide range of protocols, including SAS, PCIe, Ethernet, and more, ensuring optimal performance for your equipment.

Industry standards: Support for SAS 3.0/4.0, PCIe Gen 3/4/5, 25G Ethernet, and 56GT/s PAM4 means that you can trust that your equipment will perform at optimal levels without any signal loss or degradation.

PCI-E 5.0 Mini Cool Edge IO MCIO PCI-E 4i 38Pin Male to SFF-8654 Slimline 4X Extender Cable 50cm

High-speed data transfer: This cable is designed for use with ssd that use MICO to SFF-8654 connectors, allowing for fast and reliable data transfer at speeds of up to 24 Gbps.

Easy to use: Simply plug in the SFF-8654 38Pin end of the cable into your device and the MCIO end into your external hard drive, and you're ready to go.

Mini Cool Edge IO (MCIO) cable assemblies,These products can provide high performing channels with the added flexibility of where/how to use signals in your system.

What is mini cool edge Io (MCIO): MCIO cables are designed for data center, networking and telecommunications markets that use SAS, PCIe, Ethernet and othersignal protocols.

The solution can support cable to board and card to board applications in system, which include chip to chip, chiptomodule, chip to board and card edge option.

High-performance cable for networking and server equipment: The MCIO Mini Cool Edge IO is designed to support a wide range of protocols, including SAS, PCIe, Ethernet, and more, ensuring optimal performance for your equipment.

Industry standards: Support for SAS 3.0/4.0, PCIe Gen 3/4/5, 25G Ethernet, and 56GT/s PAM4 means that you can trust that your equipment will perform at optimal levels without any signal loss or degradation.

PCI-E 5.0 Mini Cool Edge IO MCIO PCI-E 4i 38Pin Male to SFF-8611 Oculink 4X Extender Cable 50cm

High-speed data transfer: This cable is designed for use with ssd that use MICO to SFF-8611 connectors, allowing for fast and reliable data transfer at speeds of up to 24 Gbps.

Easy to use: Simply plug in the SFF-8611 end of the cable into your device and the MCIO end into your external hard drive, and you're ready to go.

Mini Cool Edge IO (MCIO) cable assemblies,These products can provide high performing channels with the added flexibility of where/how to use signals in your system.

What is mini cool edge Io (MCIO): MCIO cables are designed for data center, networking and telecommunications markets that use SAS, PCIe, Ethernet and othersignal protocols.

The solution can support cable to board and card to board applications in system, which include chip to chip, chiptomodule, chip to board and card edge option.

High-performance cable for networking and server equipment: The MCIO Mini Cool Edge IO is designed to support a wide range of protocols, including SAS, PCIe, Ethernet, and more, ensuring optimal performance for your equipment.

Industry standards: Support for SAS 3.0/4.0, PCIe Gen 3/4/5, 25G Ethernet, and 56GT/s PAM4 means that you can trust that your equipment will perform at optimal levels without any signal loss or degradation.

PCI-E 4.0 4X Host Adapter to NVMe Ruler 1U GEN-Z EDSFF Short SSD E1.S with Heat Sink Carrier Adapter

EDSFF offers a dynamic range of form factors that have advantages vs the incumbent SSD form factors in capacity, scalability, performance, serviceability, manageability, thermal and power management.

This converter enables the connection of a GEN-Z SSD in E1.S. Fit for 9.5mm & 15mm & 25mm thickness SSD with heat sink.（like PM9A3 PM9D3 P5801X)

The converter can be installed into your system internally through the PCI-E 4X interface.

Thus an EDSFF E1.S SSD becomes an PCI-E SSD, which can be used in IoT, data center and server area.

Compliant with PCI Express 4.0. No driver installation is required. Most of the latest operating systems support PCIe-NVMe SSDs.

Low profile and Regular size PCIe bracket on board.

U.2 SFF-8639 Host Adapter to NVMe Ruler 1U GEN-Z EDSFF 2C 8X Short SSD PM983 E1.L Carrier Adapter

This converter enables the connection of a GEN-Z 2C Connector 8X SSD in E1.L.

This card expands the PC by one EDSFF E1.L 2C Connector 8X interface. It can be connected e.g. to the DC PM983 Series EDSFF NVMe SSD.

The converter can be installed into your system internally through the U.2 interface.

Thus an EDSFF E1.L SSD becomes an U.2 SSD, which can be used in IoT, data center and server area.

Compliant with PCI Express 4.0. No driver installation is required. Most of the latest operating systems support PCIe-NVMe SSDs.

U.2 SFF-8639 Host Adapter to NVMe Ruler 1U GEN-Z EDSFF Short SSD P4511 E1.S Carrier Adapter

This converter enables the connection of a GEN-Z SSD in E1.S.

This card expands the PC by one EDSFF E1.S interface. It can be connected e.g. to the DC P4511 Series EDSFF NVMe SSD.

The converter can be installed into your system internally through the U.2 interface.

Thus an EDSFF E1.S SSD becomes an U.2 SSD, which can be used in IoT, data center and server area.

Compliant with PCI Express 4.0.

No driver installation is required. Most of the latest operating systems support PCIe-NVMe SSDs.

Low Profile PCI-E Express 1X Slot Riser Card Extender Extension Ribbon Flex Relocate Cable 10cm 90 Degree Angled

The angled type Allowing you to connect it to a female port, even if space around the port is limited.

This riser card faces away from the mainboard; however, since it is flexible, it can be redirected. Please ensure that PCIE cards are securely mounted in an EMI safe location, and that no shorts have occurred due to poor PCIE card placement. The unit has additional power cable to ensure proper power support.

This is PCI-e (PCI Express) 1X Slot Relocate FPC Cable.Length:10cm,It is especially suitable for custom enclosures and low-profile rack mount chassis.

High Quality Flex Ribbon Riser Card. No Driver necessary and not support hot swappable.

The Flexible Slot PCI-Express 1x Riser Card makes the PCI Express 1x Card away from motherboard , with the PCI Express socket directly in line with the socket on the motherboard.

Four Slimline SFF-8654 4X 4 NVME to PCIE Express 3.0 4.0 Raid Card VROC Raid0 Hyper Adapter

1.The product does not support hardware raid, the product only supports the formation of virtual raid under win10 system, or the use of other third-party software to build raid.

2.Only supports motherboards with detachable PCI-E channels.Control the operation of two disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.

3.Four Slimline SFF-8654 4X design, Stable installation, Can run 4 PCIE disks at full speed at the same time.

4.Built-in multiple sets of high-power DC modules for sustainable and stable work.

5.The innovative design can accommodate Four PCIEs of the chassis, and can support simultaneous operation.

Dual 2X NVME M.2 AHCI to PCIE Express 3.0 4.0 Slimline SFF-8654 8X Raid Card VROC Raid0 Hyper Adapter

1.The product does not support hardware raid, the product only supports the formation of virtual raid under win10 system, or the use of other third-party software to build raid.

2.Only supports motherboards with detachable PCI-E channels.Control the operation of two disks based on the motherboard PCIE channel,The motherboard without PCIE signal split can only recognize one disk.

3.NVME two-disks design, Stable installation, Can run 2 NVME disks at full speed at the same time.

4.Built-in multiple sets of high-power DC modules for sustainable and stable work.

5.The innovative design can accommodate two NVMEs of the chassis, and can support simultaneous operation.

PCI-E Gen3.0 1x To 16x Riser Cable 30cm PCI-Express PCI-E X16 Extender Right Angled Elbow Design

Work For GTX1080TI high-end graphics CARDS, firepro w7100, radeon hd RX580 VEGA64, pro wx5100, quadro K1200 professional graphics,support all the PCIe card

EP-114 series is PCIe 1x to 16x Edge Connector Extension Adapter cable, adapted to PCIe x16,connectors to re-locate a PCIe card slot or bridge between slots on two different PCBs.

The ribbonized format of the axial cable provides a dense and flexible solution without signal attenuation for high speed PCIe Gen3 8Gbps Data Transaction, bidirectional 256Gbps (256GT/sec) for PCI x16, and 16Gpbs (16GT/sec) per PCIe lane.

Cable Quality: Stable PCIe Gen3 8Gbps or higher with high quality Axial Cable

Cable Flexibility: Highly-routable, foldable, flexible

Cable Length: 30cm

PCB Quality: Experienced design and durable material for High frequency and low attenuation.

Connector Quality: Taiwan Made high quality for PC server / mother board.

Solder Point Protection: PCB-Swaddled and fixed with Bolts and nut to prevent tearing and short circuit for PCB-Cable solder points.

Specification:

1.Maximum Speed: PCIe Gen3 8Gbps. Bidirectional 32.0GB/sec (256Gpbs , 256GT/sec) for PCIe x16, 2.0GB/sec (16Gpbs , 16GT/sec) per PCIe lane, PCIe Gen2 (5Gbps) PCIe Gen1 (2.5Gbps) compatibles.

2.Header (Male) Connector: PCIe x1

3.Receptacle (Female) Connector: PCIe x16

4.Cable: Length: Customized for 30cm

5.Cable Type: Flat, Twin Axial, Thickness=1.4mm (1/16 inch) Width=54mm (9mm*6, 2 1/8 inch)

6.EMI Shielding with Conducting Polymer

7.Connector Type: Straight , Up angles, Down angled

NGFF M.2 Key-A to Mini PCI-E PCI Express Converter Adapter for 9260 8265 7260 AC Wifi Bluetooth Wireless Card

Support hot plug,plug play.No need extra power adapter and any drivers.

Interface type:Key A M.2/NGFF to PCI-e

System Requirement:Windows 10 Windows 7, Windows 8

Note: Only support KEY A or KEY A+E to PCI-E(The single Key E interface can't be used),Not fit SSD ,3G/4G module card

Can support Almost NGFF M.2 Wireless Card,such as 8260NGW,8265NGW,7260NGW,7265NGW BCM94352Z;

PCI-E Express 1x To 16x Extension Flex Cable Extender Converter Riser Card Adapter 20cm

- layer PCB bard designing.

-1-slot PCI-E 1X riser card with normal ribbon cable.

- high speed FFC cable is flexible for 1U,2U,3U chassis.

- Support PCIe 1X card and 4X,8X,16X card( only provide 1X speed).

PCI-E Express 16X to 16x Male to Female Riser Extender Card Ribbon Cable 20cm

- layer PCB bard designing.

-1-slot PCI-E 16X riser card with normal ribbon cable.

- high speed FFC cable is flexible for 1U,2U,3U chassis.

- Support PCIe 1X card and 4X,8X,16X card.

PCI-E Express 1X Slot Riser Card Extender Extension Ribbon Flex Relocate Cable

This is PCI-e (PCI Express) 1X Slot Relocate Cable.

High Quality Flex Ribbon Riser Card. No Driver necessary and not support hot swappable.

The Flexible Slot PCI-Express 1x Riser Card makes the PCI Express 1x Card away from motherboard , with the PCI Express socket directly in line with the socket on the motherboard.

Length:20cm

Fully compliant with USB specification revision 2.0

Supports USB-based ExpressCard/34mm devices

Support data transfer rate up to 480Mb/s

Hot-plug support allows you to connect /remove this

Adapter without turning off your system

Quickly and easily adapts ExpressCard/34 (USB-based) devices to work through your notebook's CardBus slot

Work with USB-based ExpressCard devices including broadband wireless modem (such as CDMA, EV-DO, GPRS, etc.), flash memory, flash cards adapters, security, legacy I/O(PS2, serial, parallel), optical disk drives, GPS receivers, and more..

Supports Windows 2000/XP/Server 2003/Vista/Windows 7

PCI-E Express 8X to 8x Male to Female Slot Riser Extender Card Ribbon Flexible Cable 20cm

Layer PCB bard designing.

1-slot PCI-E 8X riser card with normal ribbon cable. Length: 20cm

high speed FFC cable is flexible for 1U,2U,3U chassis.

Support PCIe 1X card and 4X,8X card.

4 Hard Disk Control System Intelligent Control Management System HDD SSD Power Switch with PCI Bracket

4 way hard disk power switch management and control system

Support: ATX standard chassis

Advantages: safe and stable 4 way hard disk independent switch control and management system, lead-free high temperature SMT, durable.

Usage: System control 4 hard disks on and off, energy saving and environmental protection, prolong the hard disk life, ensure data security.

3 Hard Disk Control System Intelligent Control Management System HDD SSD Power Switch

with 8cm Low Profile Bracket

3 way hard disk power switch management and control system

Support: ATX standard chassis

Advantages: safe and stable 3 way hard disk independent switch control and management system, lead-free high temperature SMT, durable.

Usage: System control 3 hard disks on and off, energy saving and environmental protection, prolong the hard disk life, ensure data security.